Teltonika RUT901

Mobile module - 4G LTE Cat 4 up to 150 DL/50 UL Mbps; 3G up to 21 DL/5.76 UL Mbps; 2G up to 236.8 DL/236.8 UL kbps

3GPP Release - Release 9

SIM switch - 2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protection

Status - IMSI, ICCID, operator, operator state, data connection state, network type, bandwidth, connected band, signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, data sent/received, LAC, TAC, cell ID, ARFCN, UARFCN, EARFCN, MCC, and MNC

SMS - SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP

USSD - Supports sending and reading Unstructured Supplementary Service Data messages

Black/White list - Operator black/white list (by country or separate operators)

Multiple PDN - Possibility to use different PDNs for multiple network access and services

Band management - Band lock, Used band status display

SIM idle protection service - When working with devices with two SIM slots, the one not currently in use will remain idle until the device switches to it, meaning that no data is used on the card until then

SIM PIN code management - SIM PIN code management enables setting, changing, or disabling the SIM card's PIN

APN - Auto APN

Bridge - Direct connection (bridge) between mobile ISP and device on LAN

Passthrough - Router assigns its mobile WAN IP address to another device on LAN

Wireless mode - 802.11b/g/n (Wi-Fi 4), Access Point (AP), Station (STA)

Wi-Fi security - WPA2-Enterprise - PEAP, WPA2-PSK, WPA-EAP, WPA-PSK, WPA3-SAE, WPA3-EAP, OWE; AES-CCMP, TKIP, Auto-cipher modes, client separation, EAP-TLS with PKCS#12 certificates, disable auto-reconnect

SSID/ESSID - SSID stealth mode and access control based on MAC address

Wi-Fi users - Up to 100 simultaneous connections

Wireless Connectivity Features - Fast roaming (802.11r), Relayd, BSS transition management (802.11v), radio resource measurement (802.11k)

Wireless MAC filter - Whitelist, blacklist

Wireless QR code generator - Once scanned, a user will automatically enter your network without needing to input login information. 

WAN - 1 x WAN port 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX

LAN - 3 x LAN ports, 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX

Routing - Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), Policy based routing

Network protocols - TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL/TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SNMP, MQTT, Wake On Lan (WOL)

VoIP passthrough support - H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets

Connection monitoring - Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection

Firewall - Port forward, traffic rules, custom rules

Firewall status page - View all your Firewall statistics, rules, and rule counters

Ports management - View device ports, enable and disable each of them, turn auto-configuration on or off, change their transmission speed, and so on

Network topology - Visual representation of your network, showing which devices are connected to which other devices

Hotspot - Captive portal (hotspot), internal/external Radius server, Radius MAC authentication, SMS authorisation, SSO authentication, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, 9 default customisable themes and optionality to upload and download customised hotspot themes

DHCP - Static and dynamic IP allocation, DHCP relay, DHCP server configuration, status, static leases: MAC with wildcards

QoS / Smart Queue Management (SQM) - Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e

DDNS - Supported >25 service providers, others can be configured manually

DNS over HTTPS - DNS over HTTPS proxy enables secure DNS resolution by routing DNS queries over HTTPS

Network backup - Wi-Fi WAN, Mobile, VRRP, Wired options, each of which can be used as an automatic Failover

Load balancing - Balance Internet traffic over multiple WAN connections

SSHFS - Possibility to mount remote file system via SSH protocol (not available in standard FW)

Authentication - Pre-shared key, digital certificates, X.509 certificates, TACACS+, Internal & External RADIUS users authentication, IP & login attempts block, time-based login blocking, built-in random password generator

Firewall - Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T

Attack prevention - DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)

VLAN - Port and tag-based VLAN separation

Mobile quota control - Mobile data limit, customizable period, start time, warning limit, phone number

WEB filter - Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only

Access control - Flexible access control of SSH, Web interface, CLI and Telnet

SSL certificate generation - Let's encrypt support

OpenVPN - Multiple clients and a server can run simultaneously, 27 encryption methods

OpenVPN Encryption

IPsec - XFRM, IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16)

GRE - GRE tunnel, GRE tunnel over IPsec support

PPTP, L2TP - Client/Server instances can run simultaneously, L2TPv3, L2TP over IPsec support

Stunnel - Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code

DMVPN - Method of building scalable IPsec VPNs

SSTP - SSTP client instance support

ZeroTier - ZeroTier VPN client support

WireGuard - WireGuard VPN client and server support

Tinc - Tinc offers encryption, authentication and compression in it's tunnels. Client and server support.

Supported modes - Server, Client

Supported connection types - TCP

Custom registers - MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Client functionality

Supported data formats - 8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII

Protocol - HTTP(S), MQTT, Azure MQTT, Kinesis

Data to server - Extract parameters from multiple sources and different protocols, and send them all to a single server; Custom LUA scripting, allowing scripts to utilize the router's Data to server feature

Modbus MQTT Gateway - Allows sending commands and receiving data from MODBUS Server through MQTT broker

Supported modes - Station, Outstation

Supported connection - TCP

DLMS Support - DLMS - standard protocol for utility meter data exchange

Supported modes - Client

Supported connection types - TCP

Teltonika Networks Web API (beta) support - Expand your device's possibilities by using a set of configurable API endpoints to retrieve or change data. For more information, please refer to this documentation: https://developers.teltonika-networks.com

WEB UI - HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, multiple event log servers, firmware update availability notifications, event log, system log, kernel log, Internet status

FOTA - Firmware update from server, automatic notification

SSH  - SSH (v1, v2)

SMS - SMS status, SMS configuration, send/read SMS via HTTP POST/GET

Call - Reboot, Status, Mobile data on/off, Output on/off, answer/hang-up with a timer, Wi-Fi on/off

TR-069 - OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem

MQTT - MQTT Broker, MQTT publisher

SNMP - SNMP (v1, v2, v3), SNMP Trap, Brute force protection

JSON-RPC - Management API over HTTP/HTTPS

RMS - Teltonika Remote Management System (RMS)

Cloud of Things - Allows monitoring of: Device data, Mobile data, Network info, Availability

ThingWorx- Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type

Cumulocity - Allows monitoring of: Device Model, Revision and Serial Number, WAN Type and IP, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength

Azure IoT Hub - Can send device IP, Number of bytes send/received, Temperature, PIN count to Azure IoT Hub server

CPU - Mediatek, 580 MHz, MIPS 24KEc

RAM - 128 MB, DDR2

FLASH storage - 16 MB, SPI Flash

WEB UI - Update FW from file, check FW on server, configuration profiles, configuration backup

FOTA - Update FW

RMS - Update FW/configuration for multiple devices at once

Keep settings - Update FW without losing current configuration

Factory settings reset - A full factory reset restores all system settings, including the IP address, PIN, and user data to the default manufacturer's configuration

Operating system - RutOS (OpenWrt based Linux OS)

Supported languages - Busybox shell, Lua, C, C++

Development tools - SDK package with build environment provided

GPL customization - You can create your own custom, branded firmware and web page application by changing colours, logos, and other elements in our firmware to fit your or your clients’ needs

Package Manager - The Package Manager is a service used to install additional software on the device

Input - 1 x Digital Input, 0 - 6 V detected as logic low, 8 - 30 V detected as logic high

Output - 1 x Digital Output, Open collector output, max output 30 V, 300 mA

Events - Email, RMS, SMS

I/O juggler - Allows to set certain I/O conditions to initiate event

Connector - 4-pin industrial DC power socket

Input voltage range - 9 – 30 VDC, reverse polarity protection; surge protection >31 VDC 10us max

PoE (passive) - Passive PoE over spare pairs. Possibility to power up through LAN1 port, not compatible with IEEE802.3af, 802.3at and 802.3bt standards, Mode B, 9 - 30 VDC

Power consumption  < 2 W idle, < 7 W Max

Ethernet - 4 x RJ45 ports, 10/100 Mbps

I/O’s - 1 x Digital Input, 1 x Digital Output on 4-pin power connector

Status LEDs - 1 x Bi-color connection status, 5 x Mobile connection strength, 4 x ETH status, 1 x Power

SIM - 2 x SIM slots (Mini SIM - 2FF), 1.8 V/3 V, external SIM holders, eSIM (Optional)

Power - 1 x 4-pin power connector

Antennas - 2 x SMA for LTE, 2 x RP-SMA for Wi-Fi antenna connectors

Reset - Reboot/User default reset/Factory reset button

Casing material - Aluminium housing, plastic panels

Dimensions (W x H x D) - 110 x 50 x 100 mm

Weight - 297 g

Mounting options - DIN rail, wall mount, flat surface (all require additional kit)

Operating temperature  -40 °C to 75 °C

Operating humidity -  10% to 90% non-condensing

Ingress Protection Rating - IP30

Regulatory - CE, UKCA, IMDA, Anatel, RCM, E-mark, ECE R118, CB, RoHS, REACH, NCC

Standards

ESD - EN 61000-4-2:2009

Radiated Immunity - EN IEC 61000-4-3:2020

EFT - EN 61000-4-4:2012

Surge Immunity (AC Mains Power Port) - EN 61000-4-5:2014 + A1:2017

CS - EN 61000-4-6:2014

DIP - EN 61000-4-11:2020

Standards

Standards